Why Spin the Slurry?
Why Spin the Slurry?
A guest post by Jonathan Gagné
From Scott: The history of The Spin is murky…although it’s often called the “Rao Spin,” I did not invent the spin. It’s likely that James Hoffmann was the first person to spin the slurry. Almost everyone to whom I’ve shown The Spin has immediately adopted it. It’s easy to execute well and it works, pretty much every time.
Jonathan Gagné, an astrophysicist based in Montreal, came to my roasting masterclass this past November. I’ve been fortunate to befriend Jonathan, as I’ve always wanted to have an astrophysicist on speed dial to call when I have a question about how things work :). I’ve been helping Jonathan with his coffee making and he’s been providing some great coffee-analysis resources, some of which I hope appear on this blog.
I asked Jonathan to explain why he believes The Spin works and we decided to publish his answer as a guest post here. This post and a few more technical discussions on coffee brewing are also available on his blog at https://coffeeadastra.com.
Why Spin the Slurry ?
Summary
In this post we will discuss the physics behind why spinning the V60 during a brew is a useful method to obtain a more uniform extraction. While spinning is helpful, it’s important not to overdo it - it can cause fine coffee grounds to migrate to the bottom of the slurry and clog the filter, slowing the drawdown and imitating a brew made with a lower-quality grinder.
Spinning the slurry during a V60 brew is useful to minimize the channeling of water that can lead to an uneven extraction. The reason why this is true can be understood with the help of physics.
A rotating slurry will experience a centrifugal force*, which means that every drop of water and every particle of coffee will suffer a force that pushes them outwards. In physics, the strength of centrifugal force is more important for heavier objects, and because of this, water will tend to migrate outward more than coffee because water is heavier.
When you brew coffee, the main cause of channeling is that dry coffee repels water more than wet coffee does. The physics behind this effect are not fully understood: they are related to the fact that molecules of water bond with each other, and dry coffee doesn’t bond with them in the same way. At first pour, water might begin travelling through a tiny hollow on the surface of the dry coffee, and then it will prefer to keep traveling through that same tunnel, because the rest of the coffee bed is still dry and repels water. In practice, a coffee bed will often develop several channels if you don’t take steps to avoid it.
When you rotate a channeled coffee bed, the water flowing down the narrow tunnels is forced out of them by the centrifugal force, and the water will wet some of the dry coffee. This horizontal re-mixing of the slurry will cause channeling to decrease overall.
There is, however, a drawback if you spin too much. As mentioned earlier, heavier things are more affected by the centrifugal force. The largest coffee particles will thus experience a stronger pull toward the walls of the V60. In a slurry where coffee is mixed with water, this effect will be slightly reduced by water friction. Think of trying to run in the sea - the friction water exerts on you will slow down your movement, especially if you present it with a large surface, for example by wearing saggy pants. The friction is however not strong enough to completely stop the migration of particles based on their size, and the larger coffee particles will be sent outwards.**
This whole situation presents the smallest particles with an opportunity: the larger ones having moved out of the way, fines will sink down to the bottom of the V60, where they will be free to do their worst at clogging the paper filter. This will significantly slow down the flow of your brew.
As an illustration of this, I recently brewed a few V60s with a prewet-plus-two-pours method, performing a spin right after the prewet, and right after each of the two pours. At first I did not pay too much attention to how long or how strong I was spinning, and I experienced large inconsistencies in my brew time (up to ~20 seconds), which led to inconsistencies in average extraction yields by about 0.7%. I was controlling everything else, including the height from which I poured, the flow rate, timing, grind size, slurry temperature, etc.
I then tried timing my spins, and found that using seven-second spins resulted in a 5:18 drawdown time, while two-second spins resulted in a much shorter 4:28 drawdown time! This is a nice demonstration that fines can migrate and clog your filter if you spin too much. Adjusting the grind size appropriately to maximize extraction yield and avoid astringency, I found that the two-second spins resulted in a brighter and more enjoyable cup.
In summary, you want to spin just enough to break the up channels, but not so much that fines clog the bottom of the filter.
*NB: I can already hear the interwebs shouting “CENTRIPETAL NOT CENTRIFUGAL”. Both concepts are valid and useful tools: when you stand outside of a rotating system and want to describe forces acting on that system that keep it together, the concept of a centripetal force (directed toward the center) is appropriate. It describes the external force that allows the system to keep going in this rotating motion without splattering everywhere around. In our case, this force is provided by the walls of the V60, preventing the slurry from flying around and messing up your counter. If, however, you take the point of view of the things rotating (the water and coffee), then the concept of a centrifugal force becomes very useful. You can then describe the system as if it was not rotating, by just adding a slight modification: you add an artificial “pseudo force”, also called an “inertial force” that points toward the outside, in our case the “centrifugal force”. It is often called an “inertial force” because it arises from the fact that your frame of reference (the V60 in this case) is rotating (in technical terms, it is “not inertial”). A “pseudo force” is by no means a false thing or an invalid concept, as long as you understand where it arises from and use it carefully — in fact, one can even see gravity as a pseudo force (Einstein realized that), yet it is very useful in everyday situations to view gravity as just a normal force.
** The mass of a coffee particle is proportional to its volume, which is itself proportional to the cube of its size. The water friction that the particle experiences is proportional to its surface, or to the square of its size. As a consequence, a particle three times larger will be nine times more massive and will feel nine times more centrifugal force, but only six times more water friction. If you combine the two effects, it will therefore be pushed outwards 9 - 6 = 3 times more.